1-805-484-2992

Quotes - Sizing - Sales

Post-Harvest & Cold Storage Cooling

Rapid Cooldown & Cold Storage Holding

Overview

The clock starts at harvest - product cooled quickly holds quality and shelf life that can't be recovered later in the chain.

Freshly harvested produce carries field heat that has to come out quickly to slow respiration and spoilage - the faster a crop moves from field temperature down to its holding temperature, the more of its shelf life is preserved. A glycol chiller feeding forced-air or hydro-cooling equipment gives that rapid cooldown stage a lower, more consistent supply temperature than a general-purpose refrigeration system sized for steady-state storage alone.

Cold storage holding after cooldown is a different, steadier load - keeping a room at a constant setpoint rather than pulling a large batch of field heat all at once - but sizing still has to account for door traffic and new product being added, both of which spike the load well above the room's baseline.

Because post-harvest operations are often seasonal, with a short, intense harvest window followed by months of lighter storage-only demand, a portable or add-on packaged glycol chiller that can scale with the season is frequently a better fit than a single system sized for peak year-round.

  • Rapid post-harvest cooldown preserves shelf life that can't be recovered later
  • Cold storage holding load spikes with door traffic and new product additions
  • Seasonal harvest cycles often favor scalable portable/add-on capacity over one fixed system
Cold storage room with stacked produce crates under ceiling unit coolers
Holding storage runs steady at 34-40°F, but door traffic and new product coming in spike the load well above the room's baseline.
Cooldown leaving fluid
33-38°F
Cold storage holding
34-40°F
Sub-freezing storage
20-28°F
Freezer glycol mix
30-35% propylene

Sizing Post-Harvest & Cold Storage Cooling

Rapid cooldown (hydrocooling, forced-air cooling) is a short, intense batch load - the goal is to strip field heat from a large volume of product in hours, not hold a steady temperature. Cold storage holding is the opposite: a continuous, comparatively low-intensity load driven by room insulation, door traffic and product respiration heat, not batch throughput.

Where both duties share one site, they're almost always sized and often run as two separate demands rather than one combined peak, because cooldown's short high-intensity window rarely lines up with the steady baseline storage load.

Send Us

  • Product type and throughput volume
  • Target cooldown time and cold-storage setpoint
  • Room dimensions and insulation
  • Indoor or outdoor installation

TYPICAL RANGES BY DUTY

DutyLeaving Fluid TempLoad ProfileTypical Glycol Mix
Hydrocooling / forced-air cooldown33-38°FBatch, high peak25-30% propylene
Cold storage holding34-40°FContinuous, flat15-20% propylene
Freezer / sub-freezing storage (to the 20°F floor)20-28°FContinuous, low30-35% propylene

Ranges are typical starting points, not a substitute for a load calculation - actual leaving fluid temperature and glycol percentage depend on your product, room construction and door traffic.
Call and talk it through with an engineer: 1-805-484-2992.

Post-Harvest Cooldown and Cold Storage in Practice

Because the cooldown supply runs at the bottom of its band under a heavy batch load, and that is where a weak mix ices the chiller's evaporator. The table shows hydrocooling and forced-air cooldown at 33-38°F on 25-30% propylene, while holding sits at 34-40°F on only 15-20%. A degree or two separates the setpoints, but cooldown pulls the refrigerant side harder, so the glycol film on the evaporator surface runs closer to freezing. If a site runs both duties on one loop filled at the holding-room mix, the first hard harvest batch shows it: falling flow, a low-temperature trip and produce sitting warm. A shared loop takes the cooldown mix.

The holding room inherits cooldown work it was never sized for, and room temperature climbs with every pallet that arrives warm. It happens when a harvest crew outpaces the hydrocooler and part-cooled product is moved to storage to clear space; the product already in the room warms with it. If your peak harvest days can outrun the cooldown stage, tell us, because the fix is usually more cooldown capacity, not a bigger storage unit.

Size a fixed unit for the holding room's continuous load and treat cooldown as a separate, seasonal block that can sit idle the rest of the year. Holding runs flat at 34-40°F, so that unit stays loaded through the year and works efficiently. The cooldown block covers the batch peak at 33-38°F; a portable or add-on packaged chiller suits it because it can be valved off after harvest. Watch the fill if the two share piping: cooldown needs 25-30% propylene against 15-20% for holding, so a common loop has to be filled at the stronger figure.

Directly: removing the same field heat in half the time needs roughly twice the tons, which is why the quote asks for your cooldown target and not just product volume. As an illustration, if a batch must give up 600,000 BTU, a five-hour cooldown averages 120,000 BTU/hr, or 10 tons. Cut the target to two and a half hours and the rate becomes 240,000 BTU/hr, or 20 tons. The peak inside the window runs higher than either average, because warm product sheds heat fastest at the start. Give us the target time your quality program actually needs, not the fastest one possible, since every hour taken out of the window adds capacity that sits idle once harvest ends.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales