1-805-484-2992

Quotes - Sizing - Sales

Filtration & Fluid Management

Keeping the Loop Clean Over the System's Life

Overview

A glycol loop that isn't filtered accumulates scale and debris that show up first as fouled heat exchangers, then as chiller performance loss.

Glycol loops accumulate particulate over time from pipe scale, seal wear, and whatever gets introduced during installation or maintenance, and that debris fouls heat exchangers and erodes control valve performance long before it causes an obvious failure. Inline filtration - bag filters for coarse debris, permanent media filters for finer particulate - keeps the loop clean enough that the chiller's rated capacity actually holds up over years of service, not just at startup.

Fluid management also covers glycol concentration monitoring over time: evaporation, top-offs with plain water, and gradual degradation can all shift the actual mix percentage away from what was originally specified, which quietly changes both freeze protection and heat transfer performance. Periodic testing (a simple refractometer check) catches this before it becomes a freeze-up risk in cold weather.

Filtration and fluid management are inexpensive relative to the cost of a fouled heat exchanger or an unplanned freeze-up, and they're worth specifying as part of a new system rather than added after a problem shows up.

  • Inline filtration (bag or permanent media) protects heat exchangers and valves from loop debris
  • Glycol mix percentage drifts over time from evaporation and plain-water top-offs - test periodically
  • Filtration is cheap relative to the cost of a fouled exchanger or a cold-weather freeze-up
1

Find the debris

Pipe scale, seal wear or recent installation work

2

Choose the filter

Bag at 25-100 micron, permanent media at 5-25 micron

3

Test the mix

A refractometer check at startup, then periodically

4

Service on schedule

Replace loaded bags and clean the permanent media

Keeping the Loop Clean Over Its Life

Glycol loops accumulate particulate over time from pipe scale, seal wear, and whatever gets introduced during installation or maintenance, and that debris fouls heat exchangers and erodes control valve performance long before it causes an obvious failure. Inline filtration keeps the loop clean enough that rated capacity actually holds up over years of service, not just at startup.

Fluid management also covers glycol concentration monitoring over time - evaporation, top-offs with plain water, and gradual degradation can all shift the actual mix percentage away from what was originally specified, quietly changing both freeze protection and heat transfer performance.

Send Us

  • Whether the system is new construction or an existing loop being retrofitted
  • Known sources of particulate (pipe scale, seal wear, recent installation work)
  • Current glycol mix percentage, if known, or whether it needs testing
  • Loop volume and flow rate
  • How the loop is monitored today, if at all

FILTRATION OPTIONS

TypeTypical Micron RangeBest For
Bag filter25-100 micronCoarse debris, new installation startup
Permanent media filter5-25 micronFiner particulate, long-term loop protection

Filtration and periodic mix testing are inexpensive relative to the cost of a fouled exchanger or a cold-weather freeze-up.
Call and talk it through with an engineer: 1-805-484-2992.

Glycol Loop Filtration: Operating Questions

At startup to confirm the fill, then on a fixed routine, plus after any top-off or leak repair. There is no universal interval; the right frequency follows how often the loop is topped up. A loop that loses fluid through wash-down or seal leaks drifts faster than a tight closed loop, and every top-off with plain water pulls the percentage down. On an outdoor loop, the test that matters most is the one before the first cold spell, because a diluted mix fails on the coldest night. Log each reading so drift shows as a trend rather than a surprise.

A bag filter alone is often enough on a new, straightforward loop; add permanent media when the loop carries fine particulate or must stay cleaner long term. The two do different jobs. Bags in the 25 to 100 micron range catch coarse material such as pipe scale and installation debris, which is heaviest in the first weeks of operation. Media in the 5 to 25 micron range catches what passes a bag. A common pattern is a bag sized for startup debris, with media added once the loop settles. Choose from how sensitive the exchangers and valves on the loop are, not from habit.

Capacity drifts down slowly as exchanger surfaces foul and valves stick or wear, so the chiller looks tired long before anything fails outright. Operators see it as a setpoint that holds in spring and slips in summer, a longer pull-down after each load, or a control valve that hunts. Because the decline is gradual, it often gets blamed on the chiller. Adding filtration to an unfiltered loop stops further fouling, but it does not clean surfaces already coated; heavily fouled exchangers may still need cleaning to recover capacity.

It needs routine service: bags are replaced as they load, and permanent media is cleaned on it's own schedule. Gauges on each side of the housing make the schedule easy, since a rising pressure difference shows a loading filter before it chokes the loop. A filter left to clog cuts flow, and low flow through the chiller looks like a chiller problem when the cause sits in the filter housing.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales