1-805-484-2992

Quotes - Sizing - Sales

How to Size a Glycol Chiller

Heat Load, Flow Rate & Temperature Differential

Overview

Three numbers drive every chiller rating - how much heat you need to remove, how fast the fluid moves, and how far you're cooling it.

Every chiller sizing calculation starts with heat load - how many BTU/hr (or tons, where 1 ton = 12,000 BTU/hr) the process actually generates and needs removed. That number comes from the equipment or process itself: a fermenter's exothermic reaction rate, a compressor's rated heat rejection, a cooling tunnel's line speed and product mass. Guessing heat load from vessel size or floor space alone is the single most common sizing mistake we see.

Once heat load is known, flow rate (gallons per minute) and temperature differential (the delta-T between the fluid leaving the chiller and returning from the process) are related by one formula: BTU/hr = GPM x delta-T x 500 x specific heat factor for the glycol mix in use (about 0.96 for 20% propylene glycol, falling to roughly 0.91 at 40%; water is 1.0). A wider delta-T needs less flow for the same heat load; a narrower delta-T needs more.

The chiller itself then has to be rated to deliver that flow at that leaving fluid temperature - not just to move that many tons of refrigeration in general. A chiller rated for a given tonnage at 45°F leaving fluid temperature will deliver meaningfully less capacity at 25°F, which is why a rating always has to specify both the tonnage and the target temperature together.

  • Heat load comes from the actual process, not vessel size or floor space
  • BTU/hr = GPM x delta-T x 500 x the glycol mix's specific heat factor
  • A chiller's rated tonnage depends on the target leaving fluid temperature, not tonnage alone
1

Pull the heat load

From process or equipment data, not vessel size

2

Name the setpoint

Target LFT changes what a given tonnage delivers

3

Set the delta-T

Supply/return spread trades directly against GPM

4

Solve for flow

GPM then sets the pump and the piping sizing

Where the Real Numbers Come From

Heat load is the one number worth getting right before anything else: pull it from the equipment or process itself (a fermenter's exothermic rate, a compressor's rated heat rejection, a jacket's surface area and target temperature drop) rather than backing into it from tank volume or floor space. Every other number in a rating - GPM, delta-T, tonnage - follows from that first figure.

Once heat load and target leaving fluid temperature are set, we can confirm GPM, delta-T and the glycol mix that protects the loop at that temperature, and quote a model that actually holds the rating at your setpoint rather than at a generic 45°F test condition.

Send Us

  • Heat load in BTU/hr or tons, or the process data to calculate it
  • Target leaving fluid temperature (LFT)
  • Indoor or outdoor installation
  • Expected glycol type (food-grade propylene vs. industrial ethylene)
  • Available voltage and phase

INPUTS FOR AN ACCURATE RATING

InputWhere It Comes FromWhy It Matters
Heat loadProcess/equipment data, not vessel sizeDrives every other number in the sizing chain
Flow rate (GPM)BTU/hr ÷ (delta-T × 500 × specific heat factor)Sets pump and piping sizing
Delta-TProcess supply/return temperature spreadTrades off directly against required GPM
Target LFTThe process setpoint itselfSame tonnage delivers less capacity at a colder LFT
Glycol mixColdest temperature the loop must surviveSets both freeze protection and the specific heat factor

These five inputs are what turn a tonnage guess into a real rating.
Call and talk it through with an engineer: 1-805-484-2992.

How to Size a Glycol Chiller: Points Buyers Raise

From throughput: the product mass passing through per hour, how far its temperature has to drop, and the product's specific heat. Line speed and product weight give pounds per hour; multiply by specific heat and by the temperature drop for BTU/hr, then divide by 12,000 for tons. Add the heat the tunnel picks up on its own, such as motors, fans and warm air leaking in at the ends, which are easy to miss. Use the fastest line speed and heaviest product the line will run, not a typical shift, or the chiller falls behind on the best production days.

That works as a starting estimate: connected horsepower on a compressor or hydraulic pump converts to an approximate heat-rejection load with a standard factor. Treat it as provisional and label it that way when you send it. Horsepower describes the motor, not how hard the machine works, so a machine that runs lightly loaded most of the day rejects less than the estimate suggests. If the equipment maker publishes a heat-rejection figure, use that instead; it replaces the estimate entirely.

To the peak the process actually reaches, with a modest margin, not to the daily average and not automatically to the next size up. Sizing to the average leaves the loop warm exactly when the load is highest, such as fermentation at full activity or a batch arriving hot. Sizing far above the peak causes the opposite problem: the compressor short-cycles through most of the day, which wears it faster than running near capacity. If the peak lasts minutes rather than hours, buffer volume in the loop can carry part of it and keep the chiller smaller.

Yes, if you can read the flow and both the supply and return temperatures at the same time under full load. Multiply the GPM by the delta-T, by 500 and by the specific heat factor of the fluid actually in the loop: 1.0 for plain water, lower for glycol, and lower again as the mix gets richer. Take readings during the heaviest part of the day, because a light-shift reading undersizes the new unit. Confirm flow with a meter or the pump curve rather then the pump nameplate, and test the glycol percentage, since the factor depends on it. Divide the result by 12,000 for tons.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales