1-805-484-2992

Quotes - Sizing - Sales

Single-Phase Portable Glycol Chillers

Six plug-in CF units from 0.29 to 1.5 tons

Request a Quote

Plug-In Cooling Below 1.5 Tons

CF Series, 115V and 230V

Single-phase power is the constraint that defines this page. Where a building has only 115V or 230V single-phase service - a laboratory, a brewpub, a winery tasting room, a pilot line in a leased unit - the CF series is the complete answer up to 1.5 tons: compressor, air-cooled condenser with its own fan, a 4-gallon reservoir and a small process pump in one cabinet 33 to 37 inches tall.

The four smallest models run on 115V, and three of them on 230V as well; the CF-1A and CF-1.5A are 230V only. All six are rated at 50°F leaving water at a 90°F design ambient, and all six are published with R-513A.

Fractional-ton portable glycol chiller, representative unit

WHAT TO SPECIFY

  • Capacity at your setpoint, not at 50°F. A CF-1A is a 1-ton unit at 50°F leaving water and delivers less at a glycol setpoint; tell us the setpoint and we confirm the rating.
  • Pump flow: 0.7 GPM on the CF-.25A up to 3.6 GPM on the CF-1.5A. A long hose run or a jacket with high pressure drop is checked against it.
  • Circuit: 13 to 21 full-load amps at 115V, 7 to 20 amps at 230V. Size the branch circuit from the nameplate full-load amps, not the running current.
  • Plan the receptacle or hard-wired disconnect before delivery - at 230V it is not the outlet on the office wall.
  • Room: the unit rejects the load plus its own compressor heat into the room; 90°F design ambient, 60°F minimum.
  • Weight: 220 lbs for the three smallest, 265 to 350 lbs for the rest - built to move between use points, not to be carried up stairs.
1.5 tons

Largest single-phase unit, the CF-1.5AThat rating is at 50°F and falls at a glycol setpoint. Past it, the choices are two CF units on separate circuits or a three-phase CG portable starting at 2 tons.

Before you order

Three Numbers to Send

1.

Setpoint


The leaving fluid temperature the load needs.

Below 48°F the loop needs glycol.

2.

Load


BTU/hr, or tank volume, start and final temperature and the time allowed.

We convert it to tons at your setpoint.

3.

Power


115V or 230V single-phase, and the breaker available.

That picks between the 115V and 230V models.

CF SERIES PART NUMBERS

Part Number Series Tons (50°F) Process Flow Reservoir Voltage Full Load Amps Shipping Weight
CF-.25A CF 0.29 0.7 GPM 4 gal 115V / 230V 13 (115V) / 7 (230V) 220 lbs
CF-.33A CF 0.39 0.9 GPM 4 gal 115V 15 220 lbs
CF-.5A CF 0.5 1.2 GPM 4 gal 115V / 230V 17 (115V) / 9 (230V) 220 lbs
CF-.75A CF 0.75 1.8 GPM 4 gal 115V / 230V 21 (115V) / 11 (230V) 265 lbs
CF-1A CF 1 2.4 GPM 4 gal 230V 16.2 345 lbs
CF-1.5A CF 1.5 3.6 GPM 4 gal 230V 20 350 lbs

Ratings at 50°F leaving water and 90°F ambient. Flow is the built-in process pump's published flow. Each part number links to its full specification.

Choosing Between the Six CF Models

Six plug-in CF units from 0.29 to 1.5 tons for labs, brewpubs, tasting rooms and bench-scale process loops.

The range steps in small increments - 0.29, 0.39, 0.5, 0.75, 1 and 1.5 tons - so the usual mistake is not picking the wrong size but picking to the nameplate. A load that measures 0.4 ton at a 28°F glycol supply is not a CF-.5A duty: at that setpoint a 0.5-ton unit delivers well below its rating. Size from the capacity at your setpoint and step up a model when the numbers are close.

Compressor type

The four smallest CF models use hermetic reciprocating compressors and the CF-1A and CF-1.5A use scroll compressors. Both are sealed units; the practical difference is weight, at 345 and 350 lbs shipping for the scroll models against 220 to 265 lbs for the others.

When single-phase runs out

Above 1.5 tons there is no single-phase unit in the range. The next step is the three-phase CG portables from 2 tons, or two CF units on separate circuits where three-phase power is not available and the load can be split between them.

The other line we supply covers this range as well - see its 1/4 to 1.5 ton portable chillers on our sister chiller site.

Call and talk it through with an engineer: 1-805-484-2992

Request a Quote

Plug-In CF Chillers: Circuit and Setpoint Questions

Because at 115V it draws 21 full-load amps, more than an ordinary general-purpose receptacle circuit is built for, while at 230V the same 0.75-ton unit draws 11. The 230V connection means a dedicated circuit with the matching receptacle or a hard-wired disconnect, but it avoids running the unit at the edge of a branch circuit that nuisance-trips on a hot afternoon. The CF-.25A and CF-.5A offer the same choice at lower currents, 13 against 7 amps and 17 against 9. Only the CF-.33A is 115V-only, at 15 amps.

The reservoir holds only about 33 BTU per °F, so a warm slug lifts the leaving temperature almost at once and the compressor has to pull it back down in real time. That figure comes from 4 gallons at roughly 8.33 BTU per gallon per °F, which is where the 500 in the water heat formula comes from. For scale, a 1-ton CF-1A removes about 200 BTU a minute at 50°F, so each degree in the reservoir is about ten seconds of its full output. Draining a 2-gallon jacket of 68°F fluid back into a 30°F loop adds about 630 BTU, three minutes of the CF-1A's full rating and longer at a glycol setpoint. Where the process returns warm fluid in batches, add an external tank sized to the slug.

Yes: run them in parallel, each with its own check valve at the discharge, so a stopped unit can't become a bypass for the running one. Two CF-1.5A units give 3 tons at 50°F on single-phase power, each on its own 230V circuit at 20 full-load amps. Balance the piping so both see similar flow; their pumps move only 3.6 GPM each, and an uneven split leaves one unit doing most of the work. Set one unit a degree or so colder than the other so they stage rather than fight. It is the practical route past 1.5 tons where the building has no three-phase service.

The compressor, the voltage and the weight all change with the step from 0.75 to 1 ton. The CF-1A moves from a hermetic reciprocating compressor to a scroll, ships at 345 lbs against 265, and runs only on 230V, at 16.2 full-load amps, where the CF-.75A also offers 115V. Pump flow rises from 1.8 to 2.4 GPM. On a site with only 115V, that makes the CF-.75A the largest unit available and the CF-1A a circuit change rather then a model change. At 345 lbs, plan the CF-1A's moves between use points on a cart and level floors.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales