1-805-484-2992

Quotes - Sizing - Sales

Leaving Fluid Temperature Guide

Matching Your Process Setpoint to a Real Rating

Overview

The colder the target fluid temperature, the harder a chiller has to work for the same tonnage - leaving fluid temperature is half of every real rating.

Leaving fluid temperature (LFT) is the temperature the chiller delivers fluid at, and it's just as important to a rating as tonnage - a chiller rated for 10 tons at 45°F LFT will deliver noticeably less usable capacity if the same unit is asked to hold 25°F, because the compressor has to work harder against a lower evaporator temperature to get there. Any tonnage number without a stated LFT is an incomplete spec.

Most industrial glycol chiller applications run somewhere in the 20°F to 80°F LFT range, and where a process sits in that range matters: brewery fermentation and distillery condensing often want LFT down in the 28-34°F range, general process and machine cooling frequently run closer to 45-55°F, and some duties (packaging line cooling, for instance) can run even warmer. The colder end of that range is exactly where glycol stops being optional - plain water risks freezing in the chiller's own heat exchanger below roughly 40°F LFT.

When you send us a sizing request, the target LFT is one of the first things we need alongside heat load - it changes not just how big a chiller you need, but which model family can hit that temperature reliably at all.

  • A tonnage number without a stated leaving fluid temperature is an incomplete spec
  • Most industrial duty runs 20°F-80°F LFT; brewery/distillery work often needs 28-34°F
  • Below roughly 40°F LFT, glycol stops being optional and becomes a freeze-protection requirement
1

Take process setpoint

The process sets LFT, it is not picked for convenience

2

Find the duty band

Typical duties run from 25-38°F up to 55-80°F

3

Decide on glycol

Below roughly 40°F it protects the heat exchanger

4

Rate at that LFT

Ask for capacity at your target, not at 45°F

Setting the Right Target Temperature

Leaving fluid temperature is set by the process, not chosen for convenience - a fermentation or condensing duty that needs 28°F won't get there from a chiller rated at 45°F LFT no matter how much tonnage margin you add. The colder the target, the harder the compressor works for the same tonnage, so LFT changes which model family can even hit the number, not just how big it needs to be.

Where your process sits in the 20°F-80°F range also decides whether glycol is optional: above roughly 40°F, plain water is often workable; below that, glycol protects the chiller's own heat exchanger from freezing, independant of whatever the process fluid itself requires.

Send Us

  • Required leaving fluid temperature (not just a general 'cold' target)
  • Heat load at that temperature
  • Whether the process tolerates any temperature swing, or needs a tight setpoint
  • Indoor or outdoor installation
  • Glycol type expected (food-grade propylene vs. industrial ethylene)

TYPICAL LFT BY DUTY

DutyTypical LFTGlycol Required?
Brewery / distillery process25-38°FYes - required for the setpoint
General process / machine cooling45-55°FOften, for freeze protection margin
Packaging / warmer process cooling55-80°FSite-dependent, not always required

These are typical starting points by duty type, not a substitute for your process's actual setpoint.
Call and talk it through with an engineer: 1-805-484-2992.

Leaving Fluid Temperature in Practice

No; LFT is the temperature of the fluid leaving the chiller for the process, while ambient is the air around the unit, and each changes the rating separately. LFT sets how cold the evaporator has to run, so a colder setpoint costs capacity. Ambient sets how hard an air-cooled condenser works, so a hotter site costs capacity too. A full rating states tonnage, LFT and ambient together. Mixing them up on a request, such as entering a room temperature where the setpoint belongs, produces a quote for the wrong duty.

A fluid temperature some degrees below the product target, because heat only moves through a jacket or exchanger when the fluid is colder than the product. How far below depends on the exchanger: a jacketed tank with limited surface needs colder fluid than a plate exchanger with generous area. That is why brewery and distillery process duty sits in the 25-38°F band for the glycol rather than at the product's own temperature. If you only know the product target, send it with the exchanger details and we work out the LFT from them.

Enough to matter: capacity falls noticeably as the setpoint moves from 45°F toward 25°F, and the exact loss depends on the model and refrigerant, so it is confirmed per unit. The practical consequence is that a unit rated for 10 tons at 45°F is not a 10-ton chiller on a 35°F duty. Going colder may also call for glycol where the loop ran plain water before, which changes the flow calculation. Send the load and the new setpoint together and the quote states capacity at that LFT.

Expect less capacity from the same unit, and check the fluid before the setpoint moves. A chiller rated at a warmer LFT will only run colder if its model family reaches the new number, and it will deliver fewer usable tons there. If the loop was on plain water, or on a lean mix chosen for a setpoint above roughly 40°F, it needs glycol at a percentage suited to the new temperature before the change. Send the new setpoint and current load, and we rate the existing unit at that temperature and say whether added capacity is needed.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales