1-805-484-2992

Quotes - Sizing - Sales

Condenser Water & Remote Condenser Planning

Piping & Layout for Split-System Installations

Overview

A remote or split condenser setup trades a longer piping run for real flexibility in where the compressor package and the heat-rejection side of the system each sit.

A remote condenser configuration separates the compressor/evaporator package from the condenser itself, which is common when the mechanical room can't accommodate a full self-contained unit's heat rejection, or when the condenser needs to sit outdoors while the rest of the system stays inside. That flexibility comes with a real design requirement: refrigerant line sizing and length limits have to be calculated for the specific run, not assumed to work at any distance.

Water-cooled systems using a cooling tower or plant condenser water loop instead of a remote air-cooled condenser add their own planning requirements - condenser water flow rate, supply temperature, and water treatment all affect chiller performance, and the piping tie-in needs to be sized for the chiller's actual condenser water GPM requirement, not a generic connection size.

Because both configurations depend on details specific to the site - line run length and elevation change for remote air-cooled, or condenser water flow and temperature for water-cooled - this is one area where sending us a site sketch or basic layout alongside your load and temperature numbers gets a meaningfully more accurate installation plan than a standard packaged-unit quote alone.

  • Remote air-cooled condensers need refrigerant line sizing calculated for the actual run length
  • Water-cooled systems need condenser water flow rate and supply temperature confirmed against chiller requirements
  • A basic site sketch alongside load numbers gets a more accurate split-system installation plan
1

Pick the split type

Remote air-cooled, or water-cooled on a tower or loop

2

Measure the run

Line length and elevation change set line set sizing

3

Check condenser water

Confirm loop GPM, supply temperature and treatment

4

Sketch the layout

A basic site sketch shows where each half will sit

Planning the Split-System Layout

A remote air-cooled condenser separates the compressor/evaporator package from the condenser, which is common when a mechanical room can't accommodate a self-contained unit's full heat rejection, or when the condenser needs to sit outdoors while the rest of the system stays inside. Refrigerant line sizing and length limits are calculated for the specific run - not assumed to work at any distance.

A water-cooled system using a cooling tower or plant condenser water loop instead adds its own planning factors: condenser water flow rate, supply temperature, and water treatment all affect chiller performance, and the tie-in has to be sized for the chiller's actual condenser water GPM requirement.

Send Us

  • Remote air-cooled or water-cooled configuration
  • Approximate line run length and elevation change (remote air-cooled)
  • Condenser water flow rate and supply temperature (water-cooled)
  • A basic site sketch or layout, if available
  • Heat load and target leaving fluid temperature

REMOTE / SPLIT CONFIGURATION PLANNING

ConfigurationKey Design FactorWhat We Need
Remote air-cooledLine set sizing and length/elevation limitsRun length, elevation change, site sketch
Water-cooled (tower/plant loop)Condenser water GPM and supply temperatureFlow rate, supply temp, tie-in size

Both configurations depend on site-specific details a standard packaged-unit quote doesn't capture.
Call and talk it through with an engineer: 1-805-484-2992.

Split-System Layout: What to Settle First

There is no single distance; the allowable run is set by the refrigerant circuit and the line sizes chosen for it, so it is confirmed job by job. What we need is the routed length, not the straight-line distance on a plan: the horizontal footage as the lines will actually follow walls and racks, the number of bends, and the vertical change between the two halves. A layout that looks short on a floor plan can run long once the lines climb to a roof. Send the routed length with the rise or drop, and the line sizing is worked out for that route before the condenser location is final.

Often yes, if the loop can supply the chiller's condenser water GPM at a supply temperature the unit is rated for, with water treatment already in place. The check is spare capacity, not pipe size. The new chiller adds heat to that loop, and on water that added heat is 500 times GPM times the rise, so a loop already near its limit will see its supply temperature climb once the new unit starts, and the chillers on it give up capacity together. Send the flow the loop can spare, its supply temperature on a hot day and its treatment program, and we check the tie-in against the chiller's requirement.

Tower upkeep and water treatment, both recurring, and both of which cut chiller performance when they slip. A water-cooled unit only rejects heat as well as its condenser water allows, so the tie-in assumes someone owns the treatment program and the tower maintenance from the first day. A remote air-cooled condenser avoids that water-side work but brings a refrigerant line set with its own length and elevation limits. The choice usually turns on whether the site already runs a treated tower loop. If it does, the tie-in is incremental; if it does not, the water side is a new system to staff and budget.

Where each half goes, the path the lines or water piping will take between them, and the height difference in feet. On a water-cooled job, mark the tower or plant loop connection point; for a remote condenser, mark the roof, wall or pad it sits on. A hand drawing is fine. The detail most often missing is the vertical change: a condenser two floors up looks the same on a floor plan as one at grade, but it is sized differently. Add photos of both locations and the tie-in point if you have them.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales