1-805-484-2992

Quotes - Sizing - Sales

Pump Tank Stations & Reservoirs

Buffering & Circulating the Glycol Loop

Overview

The reservoir is the loop's buffer - undersize it and a chiller that cycles too often wears out faster than one running a properly sized tank.

A pump tank station holds the system's glycol volume and houses the circulation pump that moves fluid through the loop - reservoir volume acts as thermal buffer, smoothing out load swings so the chiller isn't short-cycling in response to every small change in demand. Undersizing the reservoir relative to total loop volume and load variability is a common cause of compressor short-cycling and premature wear.

Reservoir material - polyethylene or mild steel - depends on the glycol type, temperature range, and whether the tank needs to handle any chemical exposure from cleaning or sanitation processes nearby. Pump selection has to match both the loop's total flow requirement (from your GPM sizing) and the total dynamic head of the piping run, not just the chiller's own internal flow rating.

Reservoir and pump sizing should be confirmed against your specific loop layout - total glycol volume, piping run length and elevation change, and peak simultaneous flow demand - rather than a generic tank size matched only to chiller tonnage.

  • Reservoir volume acts as thermal buffer - undersizing it causes compressor short-cycling
  • Tank material (polyethylene vs. mild steel) depends on glycol type and any chemical exposure nearby
  • Pump sizing accounts for total loop flow and dynamic head, not just the chiller's internal rating
1

Total the loop volume

It sets reservoir size and thermal buffer capacity

2

Gauge load swings

More variability needs more buffer against short-cycling

3

Size pump to the run

Piping GPM and total dynamic head, not chiller flow

4

Pick tank material

Polyethylene or mild steel, by glycol type and exposure

Sizing the Buffer, Not Just the Pump

A pump tank station holds the system's glycol volume and houses the circulation pump that moves fluid through the loop. Reservoir volume acts as a thermal buffer, smoothing out load swings so the chiller isn't short-cycling in response to every small change in demand - undersizing it relative to total loop volume and load variability is a common cause of premature compressor wear.

Pump selection has to match both the loop's total flow requirement (from your GPM sizing) and the total dynamic head of the piping run, not just the chiller's own internal flow rating. Reservoir material - polyethylene or mild steel - follows from glycol type, temperature range, and any chemical exposure nearby.

Send Us

  • Total glycol loop volume, or the piping run to calculate it
  • GPM and total dynamic head of the piping run
  • Peak simultaneous flow demand across all connected duties
  • Glycol type and any chemical/wash-down exposure nearby
  • Indoor or outdoor installation

RESERVOIR & PUMP SIZING FACTORS

FactorWhat It Drives
Total loop volumeReservoir tank size and thermal buffer capacity
Load variabilityHow much buffer is needed to prevent short-cycling
Piping run GPM & headPump selection, sized past the chiller's own internal rating
Glycol type & exposureReservoir material (polyethylene vs. mild steel)

Sized against your specific loop layout, not a generic tank matched only to chiller tonnage.
Call and talk it through with an engineer: 1-805-484-2992.

Sizing Questions on Pump Tanks and Reservoirs

Everything the pump pushes against at design flow: friction through the supply and return piping, the pressure drop across the chiller's evaporator and each process exchanger, control valves and filters, plus static lift if the system is open. Each piece is read at the peak flow the loop will see, not the average. A glycol mix also needs more head than water at the same flow, because it is thicker, especially when cold. The usual error is choosing a pump from the chiller's internal rating, which only covers the chiller's own pressure drop, not the run out to the process and back.

Yes; a process that dumps heat in batches needs more buffer than a steady load, because the tank absorbs the spike while the chiller catches up. Without that volume, the loop temperature jumps when a batch arrives and the compressor cycles hard on either side of it. A steady load can live with less buffer as long as the chiller turns down smoothly. When you send loop volume, describe the load's pattern too: how much heat arrives, how fast and how often.

It matters: polyethylene and mild steel respond differently to chemical exposure, glycol type and temperature range. Where wash-down or CIP chemicals are used nearby, the tank has to tolerate splash and fumes on the outside, not just glycol on the inside. A mild steel tank also depends on the glycol's inhibitors and a correct concentration for internal protection, so a loop whose mix is allowed to drift puts steel at more risk. Tell us the glycol type, the temperature range and any chemicals used near the station, and the material follows from those.

Yes, with an enclosure and freeze protection matched to the site's winter design low, the same as the chiller beside it. The weak points outdoors are the parts that can hold still fluid or sit exposed: the pump casing, small instrument lines and any piping section that can be isolated and left stagnant. A correct glycol mix protects all of it, so an outdoor station's mix is set to whichever is colder, the winter low or the process setpoint, never to the process alone. Mention the outdoor siting and the winter low with the request so station, enclosure and mix are specified together.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales