1-805-484-2992

Quotes - Sizing - Sales

Replacement & Upgrade Guide

Sizing a New Unit Against an Existing Installation

Overview

Replacing a chiller is a chance to correct an old sizing mistake, not just swap in the same rating you've had for years.

An existing chiller's nameplate tonnage is a starting reference, not a target - the original unit may have been oversized as a safety margin, undersized against process growth since installation, or simply running an outdated refrigerant or glycol mix that doesn't match current practice. A replacement is the right moment to check actual heat load and target fluid temperature against what's currently installed, rather than defaulting to the same number.

If your process, tank count, or line speed has changed since the original chiller went in, size the replacement against today's actual load - see How to Size a Glycol Chiller for the calculation - rather than matching a rating that may no longer reflect real demand. If nothing has changed, the existing unit's rated tonnage and LFT are a reasonable starting point to verify against.

For a full walkthrough of evaluating whether to repair or replace, and what the swap-out process looks like, see the Replace Your Chiller section - this guide focuses specifically on getting the new unit's capacity right, whichever way that decision goes.

  • An old nameplate tonnage is a reference, not an automatic target for the replacement
  • Process or load changes since original installation should be re-sized, not assumed unchanged
  • See Replace Your Chiller for the repair-vs-replace decision and swap-out process itself
1

Read the nameplate

Record rated tonnage and leaving fluid temperature

2

Ask what changed

Process, tank count or line speed since the install

3

Recheck the load

Size to today's actual heat load if anything shifted

4

Confirm the fit

Panel, piping connections and pad space for the new unit

Sizing the Replacement, Not Just Matching the Old Unit

An old chiller's nameplate is a data point, not a target - it may have been oversized as a safety margin when it was installed, undersized against process growth since then, or running a mix or refrigerant that's no longer current practice. A replacement is the one moment in a chiller's life where re-checking actual heat load against nameplate tonnage costs nothing extra.

If your process, tank count or line speed hasn't changed since the original installation, the existing unit's rating is a reasonable starting point to verify. If anything has changed, size the replacement against today's actual load using the same method as a new installation - not the old number.

Send Us

  • Existing unit's nameplate tonnage and leaving fluid temperature
  • Whether process, tank count or line speed has changed since original install
  • Current heat load, if you have it, or the process data to calculate it
  • Existing electrical service (voltage, phase, available amperage)
  • Existing piping connections and footprint constraints

WHAT TO RE-VERIFY BEFORE ORDERING A REPLACEMENT

Nameplate ItemCheck AgainstWhy
Rated tonnageCurrent actual heat loadOriginal sizing may not reflect today's process
Leaving fluid tempCurrent process setpointA changed process can shift the required LFT
Electrical serviceSite's current panel/serviceConfirms fit before ordering, not after delivery
FootprintCurrent pad/mechanical room spaceOld unit's footprint isn't guaranteed to match new model

A replacement quote goes faster with these confirmed up front then discovered after the new unit arrives.
Call and talk it through with an engineer: 1-805-484-2992.

Sizing a Replacement Chiller: What to Recheck

Size the replacement at today's setpoint, because an old nameplate tonnage only holds at the temperature it was rated at. A unit rated at a warmer condition and now running a colder process has been delivering less than its nameplate all along, so matching that number ton for ton can leave the new unit short. The reverse happens too: an old unit rated cold and now serving a warmer duty overstates the tonnage needed. Record the nameplate's rating temperature beside its tonnage and send both with the current setpoint.

Often, but it is confirmed against the new unit's connection sizes and electrical data, not inferred from the old unit's. A new model of the same tonnage can have different connection sizes or locations, a different current draw and a different footprint, so adapters, a new disconnect or a pad extension may be needed. Those are minor items when planned and costly ones when found on installation day. Send the existing connection sizes, the panel's voltage, phase and free amperage, and photos of the piping at the unit, and we flag what has to change.

Yes, if growth is expected within a few years; replacement is the cheapest moment to provide for it. Sizing up blindly has its own penalty, though: a unit well past today's load short-cycles until the growth arrives. Often the better path is a unit sized for today, with piping, electrical and pad space laid out for an added unit later, or a format with add-on capacity. Tell us the expected growth and its timing with the request, and we compare those paths against the cost of the larger unit.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales