1-805-484-2992

Quotes - Sizing - Sales

Keg & Draft Line Cooling

Glycol-Jacketed Draft Lines & Walk-In Keg Coolers

Overview

A pour is only as cold as the last few feet of line it travels through - a glycol-jacketed run holds pour temperature the whole way to the tap.

A keg cooler holds product at storage temperature, but the draft line between the walk-in and the tap is where a warm pour usually starts - a long run without its own cooling picks up heat from the room it passes through. A glycol-jacketed trunk line, circulated from the same chiller that serves the walk-in, holds beer at pour temperature for the entire run, which matters most on longer back-bar or multi-tap installs.

Sizing here is less about tonnage and more about matching glycol supply temperature and flow rate to line length and tap count - an undersized pump or a loop that's too warm shows up as foam and inconsistent pours rather than a failed cooler. Most keg-and-draft-line jobs are a good fit for a smaller portable glycol chiller feeding both the walk-in coil and the jacketed trunk line from one unit.

This is a lighter, steadier duty than fermentation or condensing cooling, but it still needs a properly mixed glycol solution rather than plain water, since trunk lines routinely run well below what water can hold without freezing in the chiller's own heat exchanger.

  • Glycol-jacketed trunk lines hold pour temperature from the walk-in to the tap
  • Line length and tap count drive flow rate, not just chiller tonnage
  • One portable glycol chiller commonly serves both the walk-in coil and the trunk line
Insulated glycol trunk line running overhead to a draft tower at the bar
A glycol-jacketed trunk line holds the pour cold from the walk-in to the tap. Line length and tap count set the flow, at about 28-34°F.
Draft trunk line
28-34°F
Walk-in keg cooler
34-38°F
Trunk line glycol mix
25-30% propylene
Load driver
Line length, tap count

Sizing Keg & Draft Line Cooling

Draft line length and tap count drive load more than keg volume does - a long run to a remote bar or a large tap wall has to hold pour temperature over more linear feet of glycol-jacketed trunk line than a short run with a handful of taps. Walk-in keg cooler holding is a separate, steadier load layered on top.

Most draft systems run a small dedicated glycol chiller rather than sharing a production chiller, since the loop, pump and reservoir are sized specifically for trunk-line length and tap count rather than brewery process tonnage.

Send Us

  • Trunk line length and tap count
  • Walk-in keg cooler size, if applicable
  • Target pour temperature
  • Distance from cooler/chiller to the tap wall

TYPICAL RANGES BY DUTY

DutyLeaving Fluid TempLoad ProfileTypical Glycol Mix
Draft trunk line28-34°FContinuous, line-length driven25-30% propylene
Walk-in keg cooler34-38°FContinuous, flat20-25% propylene

Ranges are typical starting points, not a substitute for a line-length and tap-count calculation - actual leaving fluid temperature and glycol percentage depend on your trunk-line run and tap wall.
Call and talk it through with an engineer: 1-805-484-2992.

Draft Line and Keg Cooler Glycol: Operating Questions

That the glycol is picking up too much heat before it reaches the end of the trunk line, usually from too little flow rather than too warm a supply. If supply leaving the chiller sits inside its 28-34°F range and the near taps pour clean, the chiller is doing its job; the far end of the jacket is running warm. Check the pump, look for a kinked or crushed bundle, and measure glycol temperature at the far end. The common wrong fix is dropping the setpoint, which overcools the lines near the walk-in without curing the flow shortfall at the far end.

Yes, often more than its length does: every foot the bundle runs through a warm space adds heat the glycol must absorb before the beer reaches the tap. A trunk routed through a ceiling void over a kitchen, an attic or past a boiler room picks up far more heat per foot than one run through conditioned space. That is why we ask what the route passes through as well as the distance to the tap wall. The mistake shows up where a short run was chosen for convenience through a hot space and the pours still foam every summer. Insulation quality along the bundle matters for the same reason.

Load and pump head both rise, so check the pump before the chiller. Extra taps add product lines to the bundle, and extra distance adds trunk lenght out and back. Before expanding, log glycol supply and return temperatures at the chiller during a busy service: a wide split already means flow is marginal for today's taps. Send the existing and new trunk lengths and the tap count, and we will check both.

Because beer sitting in the lines between services warms toward room temperature once the jacket stops, and the first pours after a restart come out foamy. Holding a flat, continuous load is easy work for a draft chiller, and shutting it off overnight saves little energy while costing product at opening. The loop also runs at 28-34°F, cold enough to need a 25-30% propylene mix; if a leak has been made up with plain water, steady running is when the weak mix shows itself as slush in the chiller and falling flow. Test the fluid after any top-up.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales