1-805-484-2992

Quotes - Sizing - Sales

Repair vs. Replace Cost Guide

Weighing a Repair Bill Against Total Cost of Ownership

Overview

A repair quote and a replacement quote answer two different questions - the real comparison is repair cost against what the old unit will keep costing you.

A single repair quote compared against a new chiller's purchase price almost always favors repair - but that's the wrong comparison. The real question is what the current unit will keep costing over its remaining realistic service life: not just this repair, but the pattern of repairs likely to follow, the efficiency loss of an aging compressor, and the production risk of unplanned downtime if the next failure happens at a worse time.

A rough rule of thumb used across industrial refrigeration: if a single repair costs more than 30-50% of a comparable new unit's price, or if the unit has had multiple significant repairs in the past two years, replacement usually wins on total cost even though the upfront number is higher. That threshold moves depending on how critical the cooling duty is - a chiller feeding a single non-critical process can tolerate more repair risk than one feeding a production line that stops without it.

The most useful version of this comparison isn't abstract - it's your actual repair history against an actual replacement quote for your specific load and site conditions. Send us your current unit's age, tonnage, and recent repair history alongside your process requirements, and we can put a real replacement number next to what you're already weighing.

  • Compare repair cost against total remaining cost of ownership, not just this one repair bill
  • Rough threshold: a single repair over 30-50% of new-unit cost often favors replacement
  • How critical the cooling duty is shifts that threshold - production-line risk tolerates less repair delay

Judge the repair pattern, not the one bill in hand.

Pull 2-3 years of service invoices and set them beside a current replacement quote. A single repair over roughly 30-50% of a comparable new unit's price usually tips the total cost toward replacing.

What to Gather Before You Decide

The comparison gets easier once the numbers are in front of you instead of in memory. Pull the last two or three years of service invoices rather than just the one you're holding now - a pattern of repairs tells a more honest story than any single bill, and it's usually the pattern, not the amount, that tips the decision.

Weigh the production risk the same way: a non-critical loop can absorb another repair cycle; a line that stops without cooling generally can't afford a repeat failure at an unpredictable time.

Gather

  • Repair invoices from the past 2-3 years
  • Current unit's age, tonnage and refrigerant type
  • How critical the cooling duty is to production
  • A current replacement quote to compare against

REPAIR vs. REPLACE AT A GLANCE

Factor Repair Replace
Upfront cost Lower, one-time Higher, one-time
Downtime risk Recurring, unpredictable timing One planned changeover window
Efficiency Continues to decline with age Resets to current-generation performance
Refrigerant risk (if R-22) Ongoing, rising Eliminated
Warranty coverage Limited to the repaired component Full new-equipment warranty

General trends, not a substitute for your actual numbers.
Call and talk it through with an engineer: 1-805-484-2992.

Before You Approve Another Chiller Repair

Treat them that way, because the plant pays the total, not the largest single bill. Two repairs at 20 percent of a comparable new unit's price, inside two years, add up to 40 percent, squarely within the range where replacement usually wins. The pattern says more than the sum: two separate failures suggest more parts are near the end of their life. Add the invoices for the past 2-3 years against today's price for an equivalent new unit, and include the downtime each repair caused, which never appears on the invoice.

Measure the chiller's power draw at a known load, compare it with its nameplate or a past reading at similar conditions, then multiply the difference by run hours and your power rate. The comparison only works if load and ambient match, so take readings on comparable days, with flow and temperature drop logged at the same time to confirm the tons. A sub-meter on the chiller feeder makes this far easier than reading the plant bill, which mixes in every other load. Put the yearly figure in the repair column, alongside the repair bill, for each year the old unit would keep running. Over three or four years that line can turn out larger than the repair itself.

Yes, and it is often the biggest number there. Estimate what an hour without cooling costs in lost or scrapped product, idle labor and missed shipments, then multiply by the outage you would face, including the wait for parts or refrigerant on an older unit. A repair that takes a day of work but three weeks to source carries three weeks of risk, not one day. For a non-critical loop the figure may be small; for a line that stops when cooling stops, it frequently decides the case.

Only for the compressor. The evaporator, condenser coils, controls, fans and refrigerant piping keep their age, and so do any weaknesses that helped kill the first compressor, such as a fouled coil or a slow leak. Coverage after the repair applies to that compressor alone, while a new chiller is warranted as a whole. A compressor swap can be the right call on a unit in otherwise good shape. Ask the technician what caused the failure and whether it has been corrected, because a repeat failure on the new compressor is the costliest outcome of all: the repair bill is paid twice and the unit is no younger.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales