1-805-484-2992

Quotes - Sizing - Sales

Remote Condensers & Piping

Extending Heat Rejection Beyond a Self-Contained Unit

Overview

A remote condenser lets the compressor package and the heat-rejection side of the system sit wherever the site actually has room.

A remote condenser is specified and matched to the compressor package's exact refrigerant type, charge, and capacity - it's not an interchangeable accessory but a system component sized as part of the original chiller selection or carefully matched during a retrofit. Line set sizing (diameter and length limits) is calculated from the specific refrigerant circuit, not a generic piping table.

Elevation change between the compressor package and the remote condenser is a real design factor, since oil return through the refrigerant circuit depends on line sizing and routing being correct for the vertical rise involved - a remote condenser mounted well above or below the compressor package needs that accounted for in the piping design, not left to standard horizontal-run sizing.

See Condenser Water & Remote Condenser Planning under Installation & Site Planning for the site-layout side of this decision; this page covers the equipment and piping itself once that layout is settled.

  • Remote condensers are matched to the specific compressor package's refrigerant type and capacity
  • Line set sizing is calculated from the actual refrigerant circuit, not a generic piping table
  • Elevation change between compressor and condenser affects oil return and needs its own line sizing
1

Identify the circuit

Refrigerant type, charge and rated capacity come first

2

Check run length

Compare it to that refrigerant circuit's length limits

3

Account for rise

Vertical rise changes sizing and routing for oil return

4

Plan fan power

Condenser fan motors usually need their own circuit

Matching the Condenser to the Circuit

A remote condenser is specified to the compressor package's exact refrigerant type, charge and capacity - it's a system component sized as part of the original chiller selection or carefully matched during a retrofit, not an interchangeable accessory. Line set sizing (diameter and length limits) is calculated from the specific refrigerant circuit, not a generic piping table.

Elevation change between the compressor package and the remote condenser is a real design factor: oil return through the refrigerant circuit depends on line sizing and routing being correct for the vertical rise involved, not left to standard horizontal-run sizing.

Send Us

  • Compressor package's refrigerant type and rated capacity
  • Approximate line run length between compressor and condenser
  • Elevation change between the two locations
  • Indoor or outdoor siting for the compressor package and condenser
  • Whether this is a new system or a retrofit onto existing equipment

LINE SET DESIGN FACTORS

FactorDesign Requirement
Refrigerant type & chargeLine set sized to the specific compressor package's circuit
Run lengthCalculated against the refrigerant circuit's length limits
Elevation changeOil return requires correct sizing/routing for vertical rise

See Condenser Water & Remote Condenser Planning under Installation & Site Planning for the site-layout side of this decision.
Call and talk it through with an engineer: 1-805-484-2992.

What Engineers Ask About Remote Condenser Piping

It can, but only as an engineered match to that circuit's refrigerant, charge and capacity, never as a bolt-on. We check whether the condenser's heat rejection suits the compressor package at the site's design ambient, whether its internal volume works with the system charge, and whether its connections suit the line set the run requires. A mismatch tends to appear as high head pressure on hot days, or charge problems that are hard to trace. Send the refrigerant and capacity from the compressor package's nameplate together with the condenser's data plate, and compatibility is confirmed before we recommend the pairing.

There is no fixed limit; what counts is whether the lines are sized and routed so oil keeps returning to the compressor through the vertical rise. A condenser above the compressor package and one below it are different problems. Lines that must carry oil upward need sizing that keeps refrigerant velocity high enough to lift it, checked against the actual rise and run length together. Applying ordinary horizontal sizing to a large rise is the classic mistake, and the symptom is a compressor that slowly loses oil. Send the rise or drop in feet along with the run length.

Not inherently, but it adds field-brazed joints that a factory-sealed packaged unit does not have, so installation practice carries more of the risk. The practices that matter are brazing under a nitrogen purge, pressure testing before evacuation, a thorough evacuation and a leak check after charging. Line sets also need support and protection where they run across roofs or along walls, since vibration and physical damage cause leaks later in life. Done by a qualified refrigeration installer, the configuration itself is not the weak point.

Usually yes; its fan motors are typically powered and controled apart from the compressor package. That means a second power run to the condenser location, plus control wiring between the two halves so the fans stage with the compressor. On a rooftop condenser, the run also needs a local disconnect and a conduit route to the roof, which is easy to leave off a drawing focused on refrigerant piping. Confirm both power and control wiring against the model's electrical data before conduit goes in.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales