1-805-484-2992

Quotes - Sizing - Sales

Meat & Seafood Processing

Immersion Chill Tank & Cold-Chain Cooling

Overview

Cold-chain compliance starts on the processing floor - an immersion chill tank that can't hold its setpoint puts the whole chain at risk.

Poultry, meat and seafood processors rely on immersion chill tanks and ice-water baths to bring product down to a safe holding temperature quickly after slaughter or catch, and regulatory cold-chain requirements set both the target temperature and the time allowed to reach it. A glycol loop feeding the chill tank's heat exchanger gives a lower, steadier supply temperature than plant chilled water, which is what keeps the tank in spec as new product is continuously added.

Load on an immersion chill tank is not steady - it spikes with processing volume and drops between batches or shift changes - so the chiller has to be sized against peak simultaneous throughput, not an average across the day. Undersizing here shows up as a chill tank that slowly loses ground as volume increases, not as an obvious failure.

Wash-down and sanitation cycles common in meat and seafood plants also put moisture and chemical exposure into the equation, which is a real factor in choosing indoor vs. outdoor packaging and materials for the chiller itself.

  • Immersion chill tanks hold cold-chain temperature and time requirements after processing
  • Peak simultaneous throughput, not average volume, sizes the loop
  • Wash-down and sanitation exposure factor into indoor vs. outdoor equipment choice
Stainless immersion chill tank with product in ice water on a tiled processing floor
An immersion chill tank held at 28-34°F has to stay in spec as product keeps arriving, so it is sized for peak throughput, not the daily average.
Immersion chill tank
28-34°F
Chill room / holding
32-38°F
Chill tank glycol mix
25-30% propylene
Chill tank load
Throughput driven

Sizing Meat & Seafood Processing Cooling

Immersion chill tank load is driven by product mass and throughput, not tank volume alone - a high-throughput line pushing product through the tank continuously needs far more cooling capacity than a low-volume operation using the same size tank. The tank's water temperature has to hold its setpoint through continuous product loading, not just recover between batches.

Cold-chain compliance downstream of the tank depends on the tank holding its target temperature under real production load, which is why sizing against actual throughput - not a nominal tank volume - is the number that matters for compliance.

Send Us

  • Product throughput (lbs/hr or units/hr)
  • Tank volume and target water temperature
  • Continuous or batch processing
  • Indoor or outdoor installation

TYPICAL RANGES BY DUTY

DutyLeaving Fluid TempLoad ProfileTypical Glycol Mix
Immersion chill tank28-34°FContinuous, throughput driven25-30% propylene
Chill room / holding cooler32-38°FContinuous, flat15-20% propylene

Ranges are typical starting points, not a substitute for a load calculation - actual leaving fluid temperature and glycol percentage depend on your product mix and throughput.
Call and talk it through with an engineer: 1-805-484-2992.

Chill Tank Cooling for Meat and Seafood in Practice

Multiply product throughput by the heat each pound gives up between entering and leaving the tank, then divide by 12,000. As an illustration, if each pound must shed 30 BTU, 4,000 lb/hr puts 120,000 BTU/hr into the tank, which is 10 tons before any allowance for tank losses, makeup water or pump heat. Heat per pound depends on the product and its temperatures in and out, which is why we ask for product type, throughput and target water temperature together. Size at the highest hourly rate of the shift, not the daily total divided by hours run.

Yes: if tank-side flow drops, or supply sits at the cold end of its range for long, ice builds on the exchanger surface and insulates it. The tank then loses capacity gradually, which looks exactly like an undersized chiller. Running near the bottom of the 28-34°F chill-tank range needs strong circulation on the tank side, so if the tank falls behind late in a shift, inspect the exchanger for ice before adding capacity.

It depends on tank volume and how quickly the tank must be back at temperature, and the refill pull-down can be a bigger load than production itself. As an example, treated as water, a 1,000-gallon refill pulled down in one hour behaves like about 16.7 GPM; every 10°F of pull-down then needs roughly 83,000 BTU/hr, close to 7 tons. Allow two hours and that halves. If first product arrives before the tank reaches temperature, the chiller carries refill and production at once. Send the tank volume, the refill water temperature and the time between refill and first product, and we will check that start-of-shift case alongside the production peak.

Quote Request Form:

Questions?

1-805-484-2992

Quotes - Sizing - Sales